IGL Ecocoat Trim

0 %

(0 hodnocení)

Koupit za 1 090 Kč

Od nejoblíbenějších
Od nejlevnějších
Od nejdražších

95 %

(208 hodnocení)

IGL Ecocoat Trim – trvanlivá nano ochrana vnitřních i vnějších plastových dílů 30 ml - kit

Doprava: 59 Kč Skladem

1 090 Kč Koupit za 1 090 Kč

Popis

Balení obsahuje:

Ecocoat Trim 30 ml
Ecocoat Precoat 100 ml
Aplikátor a aplikační hadříky

Aplikace
Treatment of interior and exterior plastic parts.
Processing
• Do not apply the product at temperatures below 5°C (41°F).• Do not expose the surfaces to be treated to direct sunlight prior or during application.• The surface must not be hot during application.• Provide adequate ventilation and fresh air during application.• If the substrate was previously treated with a coating system, proper removal, preferably with a polishing agent isimportant to ensure that the products bonds with the surface.REMINDER: Always test on an inconspicuous area first. Kindly contact your local IGL Coatings representative if youneed advice.
Step 1: Cleaning the surface
• The temperature during application should be in the range of 5-40°C (41-104°F), preferably 20-26°C (68-78.8°F).• In order to permit sufficient chemical bonding of ecocoat trim to the substrate, the surface must be carefully cleaned ofall contaminants before the application. The durability of the coating depends on how well ecocoat trim has chemicallybonded with the surface.• Use ecoclean wash to thoroughly remove all remaining residue and leftover film on the surface.• Dry the surface before degreasing the surface with ecoclean precoat. It is recommended to use the IGL Microfiber Clothfor degreasing. The degreasing ensures a completely clean and reactive paint surface.• Coat the cleaned surface immediately after cleaning to prevent any contamination.
Step 2: Treatment process
• Avoid exposing the surface to direct sunlight during application.• Place a few drops of ecocoat trim on the provided application cloth in a vertical direction.• Apply the product lightly on the surface in a 3x3 feet area, in a vertical (up and down) then horizontal (left to right)motion.• Always ensure the areas coated are overlapping.• Wait for about 0.5-1 minute (or when there is a small resistance in buffing) then buff off with a clean dry IGL MicrofiberCloth.• Allow coating to cure for 1 hour (5-50°C or 41-122°F) then apply a second layer and buff off after 0.5-1 minute with aclean dry Microfiber Cloth.Important Note: Do not let the film dry sporadically. If it dries within 1 hour, the film can be removed with asmall amount of ecocoat trim. If it has been allowed to harden for more than 12 hours, it can’t be polished off.• The hydrophobic effect generally can be seen depending on the substrate, reactivity and temperature after its initialcuring stage and is further enhanced after a few hours.• Air dry the coated surface after application for approximately 4 hours and avoid contact with water.
Curing Time
• The applied coating will be ready to be buffed off in 0.5-1 minute.• The coating will be ready to be layered as follows:• 30 minutes (5-50°C or 41-122°F); or• 7 minutes (infrared short wave); or• 7-10 minutes (infrared medium wave).Important Note: Longest interlayer duration is 12 hours.• The applied coating will fully cure in 3-5 days.• During this period the surface should not be washed with any harsh shampoos, all-purpose cleaners or any productcontaining caustic soda. This will damage the hydrophobic properties.• If necessary, the coated surface may be washed with just normal water during this period.
Cleaning and Maintenance
Surfaces coated with ecocoat trim should be cleaned with cleaners in the pH range 3-9. Strong (mineral) acids or alkalis shouldbe avoided and are also unnecessary as neutral cleaners are generally sufficient to clean surfaces coated with ecocoat trim.

Zobrazit více